0

Cotizar / Comprar

Pago en línea

TYG PA5050B
VER MÁS
Marcas
TYG PA5050B
POTENCIAS
TYG
REF. PA5050B
Amplificador de 2 canales, 1100 watts/canal a 8Ω, 1850 watts/canal a 4Ω, 2500 watts/canal a 2Ω, 5000 watts a 4Ω (bridged)
1980000
$1.980.000 COP

Cotizar / Comprar

clients img
Valoración

 

Product Description

The PA5050B provides extremely high power with professional quality Performance!!

This power amplifier represents professional quality performance and at an affordable price. Perfectly suited for a wide range of sound reinforcement applications including professional touring, performing musicians, and mobile entertainers, the PA5050 is optimized to deliver high levels of sustained power, extraordinary audio performance and  reliability.

 

STEREO MODE, Both Channels Driven
8 ohms
FTC 20 Hz – 20 kHz, 0.1% THD 1050 W
EIA 1 kHz, 0.1% THD 1100 W
4 ohms
FTC 20 Hz – 20 kHz, 0.1% THD 1600 W
EIA 1 kHz, 0.1% THD 1800 W
2 ohms
FTC 20 Hz-20 kHz 0.1% THD 2000 W
EIA 1 kHz 1% THD 2500 W
BRIDGE-MONO MODE
8 ohms
FTC 20 Hz-20 kHz 0.1% THD 3200 W
EIA 1 kHz 0.1% THD 3600 W
4 ohms 
EIA 1 kHz 1% THD 5000 W
 
Distortion (SMPTE-IM) Less than 0.02%
Distortion (Typical)
20 Hz – 20 kHz: 10 dB below rated power Less than 0.02%
1 kHz and below: full rated power Less than 0.02%
Frequency Response: 20 Hz – 20 kHz, 8 ohms, LF filter bypassed, +0/-1 db
5 Hz – 50 kHz, 8 ohms, LF filter bypassed, +0/-3 db
Damping Factor: Greater   than 250 @ 8 ohm
Noise (unweighted): 100 dB below rated output (20 Hz – 20 kHz, 8 ohm load)
Input Sensitivity: 1.42 Vrms for 1050 watts into 8 ohms
Voltage Gain: 64x (36 dB) for 8 ohm load
Input Impedance: 20k ohm balanced, 10k ohm unbalanced
Controls Front: AC power switch, Ch. 1 and Ch. 2 gain control
Controls Rear: 10-pole DIP switch featuring LF filter on/off, LF filter 30/50 Hz, Clip Limiter on/off controls for each channel and switches for selecting Stereo, Parallel, or Bridge mode. Push-button circuit breaker for each channel.
Indicators: Power-On: Green LED, Protect: Red LED
Signal -30dB: Yellow LED, Clip: Red LED
Connectors Input: XLR female, TRS (1/4″), and barrier-strip screw terminals, each channel
Connectors Output: Binding posts and Speakon® outputs (Ch. 1 Speakon wired for biamp)
Cooling: Continuously variable-speed fan, rear-to-front air flow
Amplifier Protection: Short circuit, open circuit, thermal, ultrasonic, and RF protection. Stable into reactive or mismatched loads
Load Protection: On/off muting, DC fault output crowbar
Power Requirements: 100, 120 or 240 Volts AC (±10%) 50-60 Hz (factory configured)
120V models require 20 Amp service and are supplied with a NEMA 5-20 plug on the cordset.
Dimensions: 19″ (48.3 cm) wide, 5.25″ (13.3 cm) tall,
15.9″ (40.39 cm) overall depth
Weight: 75 lbs (34.02 kg) net, 87 lbs (39.46 kg) shipping
Últimos videos